Sunlu M1 3D Pen Review! Is it worth it? Buy It
The pen is safe for young children to use due to the low temperatures it needs to perform. It is also, a fairly cheap in cost, but a decent quality machine. and its a great introduction to 3d Printing for beginners from children to adults alike.
The unit comes with the power cable but it needs a power adapter to operate, so it should be included as well (purchased separately). It needs more included filament. at least three more meters, there doesn't seem to be enough to get your feet wet, if you know what I mean.
The Sunlu M1 Intelligent 3D pen (model M1) has been placed in my hands for an honest review. We all know that the Sunlu Filament is amazing, but is their hardware just as reliable? In this article, I will give you all the pros and cons of this 3d pen and if its worth the expense.
Speaking of Costs
Everyone always looks at the costs of an item before considering to purchase it. Is it worth your hard earned cash? Well, I have found that the average price range for this Sunlu M1 is as low as $15.99 and as high as $34.99, and those are great! We all believe that you get what you pay for though. If its cheap in price, it must be cheap in quality. Right?
Let us start with the unboxing. It contains the Sunlu M1 3D Pen, two finger guards, a Micro USB Cable, user manual, and two small coils of PCL filament.
For a first time user, it is always a good idea to use the finger guards that come with a 3D pen. Not all manufacturers include those. In some cases, children and adults the same, have burned the tips of their fingers when using 3D pens. Utilizing the included guards can protect you from these possible burns… but to be truthfully honest, I don’t think the Sunlu M1 needs to include them. Now don’t get me wrong, the ceramic tip does heat up to a pretty hot temperature, but I don’t think it ever gets hot enough to actually cause damage to the skin unless held or pressed against it. It’s great that they include them anyway, but I actually drew on my hand because of the low temp tip! Not recommended though, Safety First!
The Sunlu M1 comes packaged with 2 colorful (assorted) small rolls of PCL Filament, roughly 3 meters per roll. Enough to start learning the uses of the pen, but I wish it came with a bit more. It felt like I was just getting the hang of it when I ran out of PCL filament. But no worries, I had my own PLA to use with it. The Sunlu M1 is capable of using PCL and PLA Filament which is always a bonus to have a choice selection of capable materials. I only wished it could do ABS as well, but then I’m sure I would have to retract my statement on how “not hot” the ceramic tip gets.
Included with your Sunlu M1 is the Micro USB Power cable. The cable itself is about 3ft in length which gives you ample range when plugged in the wall for use. I only wish it came with a power adapter as well. Sadly you would have to use your cell phone charger adapter or purchase one separately for the M1 since it is not included. An external power bank would be a great item to purchase as well.
The Sunlu M1 3D Pen:
The Sunlu M1 comes in a variety of colors (yellow, blue, white, black, and pink) and has two buttons on it. one button to extrude the filament which is known as the Operating key and one button to select PLA or PCL mode which adjusts the needed temperatures to work with the two different filaments. I would have preferred to have an LCD screen of sorts to show myself the difference between PLA and PCL, but I think I’m just being too greedy at this point.
But, How does it Print!?
Actually, pretty damn well. I was expecting this to overheat due to a long time of usage like most 3D pens do, but it actually kept going. I used it for about 30 minutes and I let me daughter (age 14) use it for about 2 hours continuous. The extrusion of the filament was pretty clean and quick, and the filament quality was amazing. When printing in layers (horizontally) as a typical tabletop FDM printer would everything was beyond my expectations. But then I tried printing vertically or diagonally? That’s when I realized this does not compare to a tabletop printer. It doesn’t cool as fast as it prints making it almost impossible to print a simple line straight up or diagonally from one edge to another without support. This I would consider a torture test that it failed in, but it wasn’t expected to pass to begin with. I’m not too comfortable with the Gripping/handling of the pen as well, it feels off balance in a way but that is my personal opinion.
please keep in mind that I was not paid by Sunlu or Inov3D for this review, this is my unbias and honest opinion on this product. If you would like some more information on Sunlu Filament, please read 8irdyboyuk’s Review on Sunlu TPU Filament.
I liked this 3D pen so much, I ended up posting my first YouTube video on it. If you would like to see a quick filmed preview, please view below. I gave more detailed information in this article in comparison.